manualshive.com logo in svg

Cannon CT-2000, Instruction & Operation Manual, Page: 30 / 54

Share
Download
Cannon CT-2000 Instruction & Operation Manual Download Page 30

 

22

 

CT-2000 Instruction Manual 

 

Front Panel Operations 

Following a successful Cold Start (refer to 

Bath Operation

 if needed), the CT-2000 is ready for 

instructions from the user. 

 

Note:

 

Check bath fluid levels before commencing with use of the CT-2000.

 

The front panel of the CT-2000 provides a Liquid Crystal Display (LCD) screen and a simple keypad 
interface as shown in Figure 23. 

 

Figure 23: CT-2000 Front Panel 

The keypad on the front panel of the CT-2000 consists of fifteen keys: 

•

 

White buttons - numbers 0 through 9 

•

 

A white button -  decimal point (.) key 

•

 

A yellow button - 

SET TEMP

 (set temperature) key 

•

 

A yellow button - 

CAL TEMP

 (calibrate temperature) key 

•

 

A yellow button - 

MENU

 key 

 

•

 

An orange button - 

ENTER

 key 

The keys on the bottom row (non-numerical yellow and orange keys) illuminate to assist the 
operator in selecting key entry options. 

Summary of Contents for CT-2000























































Reviews:

No comments