manualshive.com logo in svg

Cannon CT-2000, Instruction & Operation Manual, Page: 26 / 54

Share
Download
Cannon CT-2000 Instruction & Operation Manual Download Page 26

 

18

 

CT-2000 Instruction Manual 

 

Bath Operation 

 

Caution:

 

Do not power on the CT-2000 without completing the installation 

requirements. Make sure the

 MAINS 

voltage specified on the rear identification 

label matches your MAINS voltage.

 

 

Note:

 

The CT-2000 stores the “last-used” temperature setting in memory. Upon 

power-up, the bath will attempt to adjust to the last known/entered 
temperature.

 

Cold Start 

The Cold Start is the normal start-up mode for the CT-2000. During the Cold Start process, the CT-
2000 performs several diagnostics (see 

Self-Test Sequence

). At the conclusion of a successful test 

procedure, the results are briefly displayed on the LCD screen. The bath heaters are activated and 
the Bath Unit begins controlling the temperature according to the most recent temperature entry. 
The current bath temperature and the target bath temperature are visible on the liquid crystal 
display (LCD) as shown in Figure 17. 

 

Figure 17: LCD Temperature Setting 

To Cold Start the CT-2000, toggle the power BATH switch up. The POWER lamp should light when 
bath power has been activated. The five LED’s in the lower row of keys will blink on and then off, 
and the instrument will emit a short “beep” tone. 

Bath Lighting 

To activate the Bath Unit fluorescent lights, toggle the LIGHTS switch up. The switch lamp indicator 
lights up when power is supplied to the fluorescent lights. 

Summary of Contents for CT-2000























































Reviews:

No comments