manualshive.com logo in svg

Cannon CT-2000, Instruction & Operation Manual, Page: 33 / 54

Share
Download
Cannon CT-2000 Instruction & Operation Manual Download Page 33

 

CANNON Instrument Company | Calibrating the CT-2000 

25 

 

Calibrating the CT-2000 

The CT-2000 has the ability to be calibrated to a temperature reference standard for any desired 
temperature, Celsius or Fahrenheit. The controls for entering the target (desired) temperature and 
the calibration at this temperature are convenient and largely intuitive. The instrument stores 
calibration corrections for every temperature integer. 

Procedure 

Use the 

CAL TEMP

 keypad option to calibrate the CT-2000 to your ASTM thermometer for a given 

temperature. 

 

Note:

 

Before calibrating the CT-2000, make sure the bath has stabilized at the 

desired temperature.

 

1.

 

Set the CT-2000 to the desired test temperature. 

2.

 

When the CT-2000 indicates that the instrument is controlling at the desired temperature, place 
the thermometer in the bath and wait for the temperature reading to stabilize (at least 10 
minutes). 

3.

 

Press the 

CAL TEMP

 key and enter the thermometer reading up to three decimal places, 

subject to the following parameters: 

a.

 

A decimal point may be included as an entry. 

b.

 

The entered temperature must be within the operational temperature range of the bath. If 
not, a 

CALIBRATION ERROR

 is displayed on the LCD screen. 

c.

 

The entered actual temperature must not cause a correction in temperature greater than    
± 2.5 °C. 

 

Note:

 

If an error is made when entering the temperature, press the 

CAL TEMP

 

button again to cancel the operation, exit the calibration screen and reurn to 
normal CT-2000 operation.

 

4.

 

When data entry is complete, press 

ENTER

 to store the calibration data. 

Summary of Contents for CT-2000























































Reviews:

No comments