manualshive.com logo in svg

Cannon CT-2000, Instruction & Operation Manual, Page: 29 / 54

Share
Download
Cannon CT-2000 Instruction & Operation Manual Download Page 29

 

CANNON Instrument Company |  Bath Operation 

21 

 

If any component of the self-test fails, a FAILED message will appear on the LCD, accompanied by an 
audible warning tone as shown in Figure 20. 

 

Figure 20: Self-Test Fail Warning Screen 

The 

ENTER

 key will flash in a repeating pattern and the heating LED will not light (see section 

Warm

 

Start

). In the event of a FAILED test, turn off the CT-2000 power for at least five seconds and then 

restart the unit. 

It may be possible to resume normal operation of the CT-2000 following a failed self-test by pressing 
the 

ENTER

 key. If 

ENTER

 is pressed, the “

Attempting Normal Operation

” LCD message appears as 

shown in Figure 21. 

 

Figure 21: Press Enter to Attempt Normal Operation 

 

Caution:

 

A failed self-test may result in flawed operation and damage to the CT-

2000. If the CT-2000 repeatedly fails the self-test sequene, call 

CANNON

 to 

arrange for a service call for the unit.

 

Following the self-test, the CT-2000 proceeds with its normal display condition provided that the 
RTD temperature sensor is connected properly. If the RTD sensor is unplugged at any time, the LCD 
displays a warning that it is necessary to reconnect the RTD before proceeding with normal bath 
operations. Refer to Figure 22. 

 

Figure 22: RTD Sensor Warning

Summary of Contents for CT-2000























































Reviews:

No comments