manualshive.com logo in svg

Cannon CT-2000, Instruction & Operation Manual, Page: 20 / 54

Share
Download
Cannon CT-2000 Instruction & Operation Manual Download Page 20

 

12 

CT-2000 Instruction Manual 

 

11.

 

Place the wider (tempered) piece of glass in the front slot furthest away from the jar. The middle 
slot is left empty to create a vapor barrier. 

12.

 

Replace the rear top cover. Align the four holes, then insert and tighten the previously removed 
screws. 

13.

 

Replace the front top cover. Line up the four holes, then insert and tighten the previously 
removed screws. 

14.

 

Ensure that the gasket forms a tight seal with the top covers of the bath: 

a.

 

Loosen the IEC lock screw securing the AC power cord to the rear panel of the electronics 
drawer.  

b.

 

Unplug all three cables (AC power, rectangular Cinch connector and round Amp connector) 
from the rear of the electronics drawer. 

c.

 

Pull out the electronics drawer using the handles installed on the front of the unit. Press 
down or pull up on the plastic release bars on either side of the drawer track to release the 
drawer, then pull the drawer completely free of the unit and set it aside. 

d.

 

When the drawer is removed, locate the four ¼-20 set screws visible at the top of the 
drawer opening underneath the bath. 

e.

 

Turn the set screws clockwise with the included Allen wrench until the top of the jar forms a 
tight seal with the covers. Tighten the set screws uniformly so the jar remains level. 

f.

 

Run the AC cord through the rear panel opening. 

g.

 

Replace the drawer in the slide tracks and push the drawer back into its opening. Insert the 
two power plugs into the rear of the drawer assembly. 

15.

 

Remove the motor-stirrer from its box. Remove the two screws on the top heater housing and 
lift off the housing. Refer to Figure 12. 

Summary of Contents for CT-2000























































Reviews:

No comments