Cannon CT-2000 Instruction & Operation Manual Download Page 37 | Manualshive

Page: 37 / 54

Cannon CT-2000 Instruction & Operation Manual Download Page 37

CANNON Instrument Company | Communication Options

29

Communication Options

Several communication options between the CT-2000 and your computer may be configured from
the

MENU

keypad option.

Change Port Speed

The

Change Port Speed

option provides a speed setting for data transfer between the CT-2000 and

a computer via the RS-232C connection. Select the baud rate (the default for most software is 9600)
in bps (bits per second) from one of the following options:

1.

1200

2.

2400

3.

8600

4.

19.2k

5.

38.4k

Keypad Sequence

MENU

>

3

>

ENTER

>

1

>

ENTER

>

Input speed choice

(1 – 5)

>

ENTER

MODE

The

MODE

keypad option permits RS-232C or RS-485 communication options.

The CT-2000 is equipped with a full-duplex RS-232C point-to-point interface as well as a half-duplex
RS-485 network interface. Commands and Queries may be sent to the CT-2000 via either interface.
Responses and Reports may be received by the master controlling computer.

This interface is configured as 8 data bits with no parity and one stop bit.

The mode of operation, polled (multi-drop) or point-to-point, can only be configured via the front
panel menu.

Procedure

To select the

MODE

option, press

2

from the

COM Setup

menu.

«
...
35
36
37
38
39
...
»

Summary of Contents for CT-2000























































Reviews:

No comments