Cannon CT-2000 Instruction & Operation Manual Download Page 9 | Manualshive

Page: 9 / 54

Cannon CT-2000 Instruction & Operation Manual Download Page 9

CANNON Instrument Company | Introduction/Installation

1

Introduction/Installation

This manual is intended to provide information on the installation, characteristics and operation of
the CANNON CT-2000 Constant Temperature Bath.

The CANNON CT-2000 Constant Temperature Bath is designed to maintain precise temperatures at
a wide range of settings for accurate viscosity measurements. Because of its temperature stability
and ease of use, it is also suitable for any other application where temperatures must be maintained
within hundredths of one degree Celsius.

The CANNON CT-2000 is designed to maintain temperatures from 10 °C to 150 °C.

Figure 1: CANNON CT-2000 Extended Range Constant Temperature Bath

Temperature Selection and Selection

The CT-2000 offers convenient keypad entry of temperature settings up to three decimal places over
the entire temperature range of the instrument. The bath temperature will remain stable within one
1/100ths of one degree of the temperature setting.

«
...
7
8
9
10
11
...
»

Summary of Contents for CT-2000























































Reviews:

No comments