Campingaz TOUR & GRILL CV PLUS, Instructions For Use Manual

Page: 14 / 96

GB
Option 2 & 3
y
Place the cartridge on the floor ensuring that the cartridge
remains upright.
y
Check that the hose is properly installed, not twisted,
tangled, squashed or overstretched. Keep it away from
heated parts (Fig. 7b & 7c).
y
Open the regulator valve by turning the control knob (1)
counterclockwise from - to + (Fig. 8a, 8b & 8c).
Campingaz
®
CV 470 PLUS cartridge:
AS CAMPINGAZ
® CV 470 PLUS
CARTRIDGES ARE
VALVE OPERATED, THEY CAN BE DETACHED FROM
THE APPLIANCE, EASILY TRANSPORTED (EVEN WHEN
NOT EMPTY) AND FITTED TO OTHER CAMPINGAZ
®
APPLIANCE IN THE
CV 470 PLUS
RANGE DESIGNED TO
OPERATE EXCLUSIVELY WITH THESE CARTRIDGES.
D. HOSE
Do not pull or pierce the hose. Keep away from any parts of the
appliance that get hot. Check that the flexible hose stretches
out normally, without twisting or pulling (Fig. 7a, 7b & 7c).
E. LID
Prior to use: Assemble the axles of the lid. Insert the pin into
the hole of the axle to secure it (Fig. 16).
Handle the lid carefully, especially when the grill is on. Do not
lean over the fire box or cooking surface as this area can get
very hot.
Lock or unlock the lid opening thanks to the silicone latches
located on the lid sides (Fig.15).
F. CHECKING FOR GAS LEAKS
Important: Never use a flame to detect a gas leak; use a gas
leak detecting fluid.
1.
In the event of a leak (smell of gas before opening the
valve), immediately take the appliance outside to a well-
ventilated area with no combustion source to locate and
stop the leak. Even if you just wish to check the sealing
of your appliance, always do so outside.
2. Keep away from flammable materials; no smoking near
the appliance.
3. Make sure the control knob is in the “OFF” position (O)
(Fig. 12).
4. Fit the regulator on the gas cartridge (see section C).
5. Use a gas leak solution to test for leaks.
6. Apply the solution to the connections between cartridge/
regulator/ hose / appliance (Fig. 10a, 10b & 10c).
7. Open the regulator valve (1) by turning counterclockwise
from - to + (Fig. 8a, 8b & 8c) (The control knob should
remain in the “OFF” (O) position). Bubbles in the gas leak
solution indicate if there is a gas leak.
8.
Close the valve at the gas cartridge.
9. The grill must not be used until all leaks have been
eliminated.
10. Disconnect the regulator from cartridge and contact the
local after sales service for assistance.
Important:
Check for leaks at least once per year and each time the gas
cartridge is replaced.
G. PRIOR TO USE
Never use the appliance until the instructions have been read
carefully and understood. Additionally, ensure that:
y
There are no leaks.
y
Make sure the burner tube is not obstructed (by spider
webs, etc.).
y
The hose does not touch any components which may get
hot (Fig. 7a, 7b & 7c).
y
Make sure the grease evacuation tray fits correctly and that
it is inserted as far as it will go (Fig. 3).
Put the cooking grid in place correctly (Fig. 4).
H. LIGHTING THE BURNER
Never light the appliance with the lid closed, only with the
lid opened.
1.
Open the cooking lid.
2. Make sure the control knob is in the “OFF” position (O)
(Fig. 12).
3. Press the control knob and then turn it counterclockwise to
the full flow position ( ) (Fig. 11-A) .
4. Wait 2 to 3 seconds and push the piezo switch ( ) several
times(Fig. 11-B).
5. If the piezo ignition doesn’t work, ignite the grill manually
(see below).
I. LIGHTING THE BARBECUE MANUALLY
1.
Open the cooking lid and remove the grid.
2. Make sure the control knob is in the “OFF” position (O).
3. Light a match and hold it up to the burner.
4.
Push the control knob and turn it counterclockwise until it is
in the full flow position ( ) (Fig. 11-A).
5. Put the grid back in place.
J. EXTINGUISHING THE BARBECUE
Turn the control knobs back in the “OFF” position (O) (Fig. 12)
and close the gas cartridge valve (Fig. 8a, 8b & 8c).
K. REMOVING OR CHANGING THE CAMPINGAZ
®
CV 470 PLUS CARTRIDGE
The cartridge may be removed even if it is not empty.
Replace the cartridge outside and away from other people.
y
Wait for the barbecue to cool down.
y
Make sure the barbecue valve is completely closed by
turning the control knob clockwise as far as it will go (Fig. 12).
y
Detach the regulator (2) from the cartridge by unscrewing
the regulator, then lift it up (Fig. 6b).
y
Push the regulator (2) onto a new cartridge and screw it tight
until you hear a click (approximately one-sixth of a turn) (Fig.
6a). Do not force the cartridge to turn further than this or you
may risk damaging the Easy Clic
®
Plus System.
L. OPERATION
It is recommended that protective gloves be worn to handle
components which may be very hot.
When in use for the first time, heat up the barbecue with
its burner in full flow position ( ) (with the lid closed), for
approximately 30 minutes in order to eliminate any odors
resulting from the paint on the new parts.
It is good practice to pre-heat your grill for a few minutes
(10-15min) before you start placing food on it. Similarly to
when you cook in a pan or in an oven, it helps you to reach
an appropriate grilling temperature and prevents food from
sticking, ensuring a crisp, brown crust. To reduce the risk of
food sticking to grid further, you can lightly brush cooking oil on
the grid, prior to use.
Cooking speed can be regulated by the control knob position:
from full flow position ( ) to reduced flow position ( ).
In order to reduce the amount of possible flare ups while
grilling, remove any excess grease or fat from the meat prior
to placing it on the grid.
If grease does catch fire during cooking, it may be necessary to
reduce the flow by moving the control knob to the ( ) position.
13