Operating Instructions and Replacement Parts List
Spraying Instructions (Cont.)
2. Point gun in a safe direction and spray.
This should clear tip of any blockage.
3. Rotate the tip back to the spray posi-
tion and continue spraying (See Fig. 5).
4. If clogging continues, replace gun filter
and consider straining the paint prior
to use.
Equipment damage
can occur if a nee-
dle or sharp object is used to clean the
tip. Tungsten carbide is brittle and can
be chipped.
FIXED TIP:
1. Depressurize and turn off the unit
per manufacturer’s instructions.
2. Lock gun trigger.
3. Remove tip and tip guard from the gun.
4. Soak tip in water or appropriate sol-
vent and brush away old paint or
impurities with a toothbrush until
the tip orifice has been cleared.
ADJUSTABLE TIP:
1. Turn adjustment knob fully counter-
clockwise to open tip to largest spray
pattern.
2. Pull trigger and spray into a bucket
or container. This should clear the tip
of any blockage.
3. If clogging continues, replace gun fil-
ter and consider straining the paint
prior to use.
CLEANING YOUR GUN:
Follow clean-
ing, use and maintenance instructions
included with your paint sprayer. After
flushing the pump and when finishing:
1. Rotate Spray Tip to the cleaning
position.
NOTICE
2. Release Trigger Lock.
3. Point Spray Gun into an empty waste
bucket and pull the Trigger. Spray at
least 1 gallon of fluid into waste
bucket. To reduce splashing, direct
the fluid stream along the inside of
the bucket and well above the fluid
level.
REFER TO PAINT SPRAYER SHUT-
DOWN PROCEDURES.
4. Depressurize and turn off sprayer per
manufacturer’s instructions.
5. With the gun pointed in a safe direc-
tion, pull the gun trigger with the
trigger lock disengaged to ensure
system is depressurized.
6. Engage Trigger Lock.
7. At this point the pump and spray
gun are clean, but still require prepa-
ration for storage. Spray Tip Guard
or any accessory being used still
require cleaning.
CLEANING SPRAY TIP GUARD:
1. Remove Spray Tip with 1” or
adjustable wrench.
2. Clean Tip Guard with a cleaning
brush.
Maintenance
Pump damage may
occur if these
instructions are not followed.
Before per
forming any main-
tenance, make sure to relieve pressure
from system and disconnect power
from sprayer.
●
Do not use oil based solvents to
clean equipment after using latex
based coatings. Use only warm
soapy water.
●
Always replace clogged gun filters,
do not attempt to clean them.
●
Carefully follow cleaning and stor-
age instructions for your sprayer.
●
Do not use metal or other hard
objects to pick dried paint material
from Spray Tip Orifice.
TRIGGER LOCK
Pulling the trigger
must not open the
gun valve when trig-
ger lock is activated.
You should be able to get the actuator
to wiggle slightly with your finger
while holding the trigger against the
!
WARNING
!
WARNING
NOTICE
trigger lock when it is in the locked
position. If you cannot, adjust the trig-
ger position by following these instruc-
tions:
1. Place trigger in locked orientation
(tabs horizontal).
2. With one hand holding trigger
lightly against lock, use a 1/4” nut
driver to turn nut in until trigger
starts to come off the lock.
3. Reverse the nut (counterclockwise)
1/2 turn.
TIP SEAL AND WASHER
Occasionally, you will need to replace
the silver seal and black washer located
inside the tip base.
1. To replace seal and washer, first
loosen tip base with adjustable
wrench, and then remove by hand.
2. Remove spray tip.
3. With Phillips screwdriver, push seal
and washer out from front of tip
base.
4. With flat side of seal facing up,
place seal in base. Make sure it lines
up properly with base.
5. Place washer in base. Make sure it
lines up properly with base.
6. Put spray tip back in tip base.
7. Reattach tip base to gun valve.
Make sure spray tip
and tip base fit snug-
ly in place. A loose
fit can lead to misdirected spray dis-
charge and a skin injection hazard.
!
WARNING
4
CLEAN
SPRAY
Figure 5 - Clean and Spray Position
SOLVENT
Figure 4 - Prevent Clogged Tip
www.chpower.com
