manualshive.com logo in svg

Cadillac SRX 2010, Owner'S Manual, Page: 338 / 471

Share
Download
Cadillac SRX 2010 Owner'S Manual Download Page 338

Vehicle Care

9-33

Notice:

Do not cover a headlamp

to improve beam cut-off when
aiming. Covering a headlamp may
cause excessive heat build-up
which may cause damage to the
headlamp.

6. Turn on the low-beam

headlamps and place a piece of
cardboard or equivalent in front
of the headlamp not being
adjusted. This allows only the
beam of light from the headlamp
being adjusted to be seen on the
flat surface.

7. Locate the vertical headlamp

aiming screws, which are under
the hood near each headlamp
assembly.

For the vehicle that is equipped
with a base level lamp (halogen
bulb), there will be one vertical
headlamp aiming screw (V1).
The aiming screw (V1) is
adjusted from the engine
compartment side of the beauty
cover.

For the vehicle that is equipped
with an up-level headlamp (HID),
there will be two vertical
headlamp aiming screws
(V1 and V2). The aiming screw
(V1) is adjusted from the engine
compartment side of the beauty
cover and the aiming screw (V2)
is adjusted through the access
hole in the beauty cover.

The aiming screw(s) can be
turned with a Phillips
screwdriver(s).

Summary of Contents for SRX 2010
























































































































































































































































































































































































































































































Reviews:

No comments