Cadillac CTS 2019 Owner'S Manual Download Page 41

Page: 41 / 350

Cadillac CTS/CTS-V Owner Manual (GMNA-Localizing-MidEast-12470572) -

2019 - crc - 6/21/18

KEYS, DOORS, AND WINDOWS

Close the trunk by pulling on the
handle. Do not use the handle as a
tie-down.

Rear Seat Pass-Through

Use the rear seat pass-through door
when transporting long items.

To open, pull down the rear seat
armrest. Pull the lever all the way
down to release the door.

To close, push it up and back into
place. Try to open the door without
pulling up on the lever to make sure it
is locked into place.

Emergency Trunk Release
Handle

Caution

Do not use the emergency trunk
release handle as a tie-down or
anchor point when securing items
in the trunk as it could damage the
handle.

If equipped, there is a
glow-in-the-dark emergency trunk
release handle on the trunk lid. This

handle will glow following exposure to
light. Pull the release handle to open
the trunk from the inside.

After pulling the emergency trunk
release handle, push the handle back
into the bezel.

Summary of Contents for CTS 2019































































































































































































































































































































































Search results

Summary of Contents for CTS 2019

Reviews:

Related manuals for CTS 2019

Brands by name

Popular brands

Cadillac CTS 2019, Owner'S Manual

Search results

Summary of Contents for CTS 2019

Reviews:

Related manuals for CTS 2019

Brands by name

Popular brands