Cadillac CTS 2019 Owner'S Manual Download Page 304 | Manualshive

Page: 304 / 350

background image

Cadillac CTS/CTS-V Owner Manual (GMNA-Localizing-MidEast-12470572) -

2019 - crc - 6/21/18

VEHICLE CARE

303

19. Stop at a safe location and check

the tire pressure. Refer to
Steps 1

–

11 under

“

Using the Tire

Sealant and Compressor Kit
without Sealant to Inflate a Tire
(Not Punctured).

”

If the tire pressure has fallen
more than 68 kPa (10 psi) below
the recommended inflation
pressure, stop driving the vehicle.
The tire is too severely damaged
and the tire sealant cannot seal
the tire.

If the tire pressure has not
dropped more than 68 kPa
(10 psi) from the recommended
inflation pressure, inflate the tire
to the recommended inflation
pressure.

20. Wipe off any sealant from the

wheel, tire, and vehicle.

21. Dispose of the used sealant

canister (5) and sealant/air hose
(6) assembly at a local dealer or
in accordance with local
regulations and practices.

22. Replace with a new canister

assembly available from your
dealer.

23. After temporarily sealing the tire

using the tire sealant and
compressor kit, take the vehicle
to an authorized dealer within
161 km (100 mi) of driving to
have the tire repaired or
replaced.

Using the Tire Sealant and
Compressor Kit without Sealant
to Inflate a Tire (Not Punctured)

To use the air compressor to inflate a
tire with air only and not sealant:

If a tire goes flat, avoid further tire
and wheel damage by driving slowly
to a level place. Turn on the hazard
warning flashers. See

Hazard Warning

.

«
...
302
303
304
305
306
...
»

Summary of Contents for CTS 2019































































































































































































































































































































































Reviews:

No comments

Related manuals for CTS 2019

Brand: Rago FABRICATION Pages: 10

Brand: GAC MOTOR Pages: 356

Brand: Magneti Marelli Pages: 2

Brand: Mercedes-Benz Pages: 296

Brand: v.link Pages: 19

1500 CLASSIC 2020

Brand: RAM Pages: 360

Brand: Menabo Pages: 8

Brand: Curt Group Pages: 3

Brand: Juna Pages: 10

Brand: Mercedes-Benz Pages: 493

Brand: Kia Pages: 25

2012 ODYSSEY EX

Brand: Honda Pages: 13

ADS Determinator

Brand: ALCOHOL DETECTION SYSTEMS Pages: 8

Brand: MSW Pages: 11

Conserve Socket

Brand: Belkin Pages: 6

Brand: Belkin Pages: 27

Brand: Belkin Pages: 61

CarAudio Connect FM

Brand: Belkin Pages: 240

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands