Cadillac CTS 2019 Owner'S Manual Download Page 191 | Manualshive

Page: 191 / 350

background image

Cadillac CTS/CTS-V Owner Manual (GMNA-Localizing-MidEast-12470572) -

2019 - crc - 6/21/18

190

DRIVING AND OPERATING

Caution (Continued)

resulting damage would not be
covered by the vehicle warranty. See

Add-On Electrical Equipment

Starting Procedure

1. With the Keyless Access system,

the Remote Keyless Entry (RKE)
transmitter must be in the
vehicle. Press ENGINE START/
STOP with the brake pedal
applied. When the engine begins
cranking, let go of the button.

The idle speed will go down as
the engine gets warm. Do not
race the engine immediately
after starting it.

If the RKE transmitter is not in
the vehicle, if there is
interference, or if the RKE
battery is low, a Driver
Information Center (DIC) will
display a message. See

Keyless Entry (RKE) System
Operation

Caution

Cranking the engine for long
periods of time, by returning the
ignition to the START position
immediately after cranking has
ended, can overheat and damage
the cranking motor, and drain the
battery. Wait at least 15 seconds
between each try, to let the
cranking motor cool down.

2. If the engine does not start after

five to 10 seconds, especially in
very cold weather (below

−

18 °C

or 0 °F), it could be flooded with
too much gasoline. Try pushing
the accelerator pedal all the way
to the floor and holding it there
as you press ENGINE START/
STOP. Wait at least 15 seconds
between each try, to allow the
cranking motor to cool down.
When the engine starts, release
the accelerator. If the vehicle
starts briefly but then stops
again, do the same thing. This
clears the extra gasoline from the

engine. Do not race the engine
immediately after starting it.
Operate the engine and
transmission gently until the oil
warms up and lubricates all
moving parts.

Stop/Start System

If equipped, the Stop/Start system will
shut off the engine to help conserve
fuel. It has components designed for
the increased number of starts.

{

Warning

The automatic engine Stop/Start
feature causes the engine to shut
off while the vehicle is still on. Do
not exit the vehicle before shifting
to P (Park). The vehicle may restart
and move unexpectedly. Always
shift to P (Park), and then turn the
ignition off before exiting the
vehicle.

«
...
189
190
191
192
193
...
»

Summary of Contents for CTS 2019































































































































































































































































































































































Reviews:

No comments

Related manuals for CTS 2019

Brand: UnderCover Pages: 16

Brand: iDataLink Pages: 9

Brand: Wagan Pages: 12

21 COVERT Series

Brand: Code 3 Pages: 16

Brand: DAVIS Pages: 32

Brand: GATmatic Pages: 13

Brand: Curt Manufacturing Pages: 6

Brand: tams elektronik Pages: 19

Brand: Hyundai Pages: 19

Brand: GARO Pages: 15

Brand: Gator Pages: 6

Brand: JBL Pages: 12

Brand: NavLinkz Pages: 23

Brand: Westin Pages: 3

Brand: Laser Pages: 3

Brand: Curt Group Pages: 2

Brand: Datsun Pages: 104

Brand: AA Products Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands