manualshive.com logo in svg

Busch-Jaeger Corridor KNX 6131/50 series, Technical Manual

Share
Download
Busch-Jaeger Corridor KNX 6131/50 series Technical Manual Download Page 68

 

Description of application and parameters

"Detector" application

 

 

 

 

KNX Technical Manual  2CKA001473B8667  

│

  06.02.2017 

│

68

 

11.3.12  General parameters — Brightness-value threshold internal (lux) 

Options: 

1 .. 400 .. 1000 

 

–  The brightness-value threshold is used to specify the lux value at which the detector is to 

start to respond. If the detector does not switch on and the measured brightness lies above 
the set threshold, no telegram is sent during movement. 

 
 

11.3.13  General parameters — Sensitivity of the watchdog 

Options: 

High 

 

Medium 

 

Low 

 

Maximum 

 

–  High: Standard - intended for indoor use. 
–  Medium: To be used when there are small interfering heat sources within the detection 

range. 

–  Low: To be used when there are large interfering heat sources within the detection range. 
–  Maximum: To be used when there are no interfering heat sources within the detection 

range. 

 
 

 

Note 

The transmission range can NOT be changed via the sensitivity. 
The sensitivity refers to sensors 1, 2, 3, 4. 

 

This parameter is not used for devices 6131/50-xxx and/or 6131/51-xxx. The 
"Sensitivity of sensor 1/2 or 3/4" parameter under the sensor selection is used 
for this purpose. 

 

 

11.3.14  General parameters — Fade in extended parameters 

Options: 

No 

 

Yes 

 

–  No: Only the most important parameters for setting the detector are displayed. 
–  Yes: All parameters are displayed, also those that are not required in most cases. 

Examples: 

■

 Extended 

parameter 

settings 

■

  Status display parameter 

■

 Brightness 

parameter 

■

  External button parameter 

 

 

 

Summary of Contents for Corridor KNX 6131/50 series







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands