manualshive.com logo in svg

Busch-Jaeger Corridor KNX 6131/50 series, Technical Manual

Share
Download
Busch-Jaeger Corridor KNX 6131/50 series Technical Manual Download Page 136

 

Description of application and parameters

Application "RTC object"

 

 

 

 

KNX Technical Manual  2CKA001473B8667  

│

  06.02.2017 

│

136

 

11.8.48  Basic stage cooling — Maximum control value (0 - 255) 

Options: 

Setting option between 0 - 255 

 

The maximum control value of the PI controller defines the maximum value outputted by the 
controller. If a maximum value under 255 is chosen, the value will not be exceeded, even if the 
controller calculates a higher control value. 

 

Note 

This parameter is only available when "Control value type" parameter is set 
either on "PI continuous, 0 – 100%," "PI PWM, On/Off“ or "Fan coil". 

 

 

11.8.49  Basic stage cooling — Minimum control value for basic load (0 to 255) 

Options: 

Setting option between 0 - 255 

 

The minimum control value of the PI controller defines the minimum value issued by the 
controller. If a minimum value that is greater than zero is selected, the controller will not issue a 
lower value, even if it calculates a control value that is lower. This parameter can be used to set 
a basic load, e.g. for operating surface cooling. Even if the controller calculates the control value 
zero, a cooling medium will flow through the cooling area to prevent the floor from heating up. 
Under "Settings of basic load," it is also possible to define whether this basic load will be 
permanently active or whether it will be switched by the "Basic load" object. 

 

Note 

This parameter is only available when "Control value type" parameter is set 
either on "PI continuous, 0 – 100%," "PI PWM, On/Off“ or "Fan coil". 

 

 

 

Summary of Contents for Corridor KNX 6131/50 series







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands