manualshive.com logo in svg

Busch-Jaeger Corridor KNX 6131/50 series, Technical Manual

Share
Download
Busch-Jaeger Corridor KNX 6131/50 series Technical Manual Download Page 186

 

Description of application and parameters

Communication objects — Object RTC

 

 

 

 

KNX Technical Manual  2CKA001473B8667  

│

  06.02.2017 

│

186

 

11.19.17 Cooling  status 

Number 

Name 

Object function 

Data type 

17 

Cooling status 

Output 

Switching 

 

The room temperature controller sends an ON telegram via the "Cooling status" object as soon 
as it is active in the cooling mode. If the controller is in the inactive zone between heating and 
cooling or is in heating mode, the room temperature controller transmits an OFF telegram on 
the "Cooling status" object.  

   

11.19.18 Basic  load 

Number 

Name 

Object function 

Data type 

16 

Basic load 

Input / output 

Switching 

 

This object uses the value 1 to activate a parameterised base load, i.e. a minimum control value 
greater than zero. The value 0 deactivates the base load. When the base load is deactivated, 
the control value can be lowered all the way to zero if necessary when the setpoint temperature 
is reached, despite the minimum value set in the parameter. 

 

Note 

Item 2: 
Deactivating the base load for a floor heating system is always useful in the 
summer, since it saves heating energy. 

 

11.19.19 Switchover  heating/cooling 

Number 

Name 

Object function 

Data type 

17 

Switchover heating/cooling 

Input / output 

Switching 

 

1.  Automatic: If the switchover between heating and cooling is performed automatically by the 

room temperature controller, then this object is used to provide information on the current 
heating (0) or cooling (1) status to the KNX bus. It is a transmitting object. 

2.  Only via object: The switchover between heating and cooling on the room temperature 

controller occurs solely via this 1-bit communication object. The value (0) activates the 
heating mode, and the value (1) activates the cooling mode. This is a receiving object. 

3.  Manual or via object: The switchover between heating and cooling on the room temperature 

controller occurs by user interaction or via the 1-bit communication object. The information 
on the respective heating (0) or cooling (1) status is available to the KNX bus. This is a 
receiving and sending object.  

 

 

 

Summary of Contents for Corridor KNX 6131/50 series







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands