manualshive.com logo in svg

Busch-Jaeger Corridor KNX 6131/50 series, Technical Manual

Share
Download
Busch-Jaeger Corridor KNX 6131/50 series Technical Manual Download Page 25

 

Product description

 

 

 

 

 

KNX Technical Manual  2CKA001473B8667  

│

  06.02.2017 

│

25

 

4.4.3 

Busch-Watchdog Sky KNX 

 

6131/40-24 

[1] 

Detector including surveillance 

[2] 

Constant light switch 

[3] 

Brightness detection 

Table 4:  Function overview of Busch-Watchdog Sky KNX 

[1]  Detector application with 2-stage switch-off function or with integrated monitoring function. 
[2]  Constant light switch with up to 2 independent channels or with a maximum of 2 outputs for brightness-

dependent switching of 2 light rows in the room. 

[3]  For the specific switch-on and switch-off of light rows dependent on room brightness. 
 

Other features 6131/40-24: 

The programming mode can be activated with the IR remote control (6010-25). This makes it 
possible to activate the programming mode without manually operating the programming button 
and without the use of a ladder. 

 

 

 

Summary of Contents for Corridor KNX 6131/50 series







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands