Bandit
Copyright 1/10
PAGE
MODELS 65XP(XL)/95
MAINTENANCE SECTION
MAINTENANCE SECTION
& 6 Lug Hubs (1/” - 0 Studs) ...................................90 - 10 ft.-lbs. Torque (1 - 16 Nm)
8 Lug Hubs (1/” - 0 Studs) .........................................90 - 10 ft.-lbs. Torque (1 - 16 Nm)
8 Lug Hubs (9/16” - 18 Studs) .....................................110 - 10 ft.-lbs. Torque (19 - 16 Nm)
8 Lug Hubs (/8” - 18 Studs) .......................................190 - 10 ft.-lbs. Torque (8 - 8 Nm) (Cone Nut)
8 Lug Hubs (/8” - 18 Studs) .......................................7 - ft.-lbs. Torque (7 - 1 Nm) (Flange Nut)
10 Lug Hubs (/” - 16 Studs) .....................................0 - 00 ft.-lbs. Torque (610 - 678 Nm)
(Consult axle manufacturers manual shipped with each machine for specific axle-stud-wheel combination lug nut torques.)
KEEP LUG NUTS PROPERLY TIGHTENED, CHECK NEW UNIT BEFORE OPERATION, CHECK
AGAIN AFTER 20-25 MILES (32-40 km) AND REGULARLY CHECK AT LEAST WEEKLY.
BASIC WHEEL TORQUE REQUIREMENTS (per mfg.)
BOLT TORQUE CHART
(THESE TORQUES ARE BASED ON DRY, CLEAN THREADS)
DESCRIPTION
BOLT SIZE TORQUE (FT.-LBS.) TORQUE(Nm)
Before tightening bolts be sure you have the correct size bolt for the correct amount of torque.
Use only factory approved knives and hardware.
Chipper Bearing Bolts (9 and 6 Belt Side)
/8” - 11 NC
10
0
Chipper Bearing Bolts (6 Infeed Hopper Side)
1/” - 1 NC
70
9
Chipper Shaft Bearing Retainer (9)
/” - 10 NC
170
0
Chipper Shaft Bearing Retainer (6)
/8” - 11 NC
10
0
Chipper Draw Ring (9)
/8” - 18 NF
10
0
Anvil (9)
/8” - 11 NC
10
16
Anvil (6)
1/” - 1 NC
6 - 7
88 - 10
Feedwheel Bearing Bolts
1/” - 1 NC
7
10
Feedwheel Bearing Set Screws (9)
/8” - NF
0
7
Feedwheel Bearing Set Screws (6)
/16” - NF
1
19
Grip-Tight Feedwheel Bearing Set Screws
Engine Hold Downs
/8” - 11 NC
1
169
Engine Hold Downs
1/” -1 NC
60
81
Engine Hold Downs
/8” - 16 NC
7
Knife Bolts (9/16” x 3 5/8” x 10 1/8” Knives - 95) 1/2” - 13 NC
70 - 80
95 - 108
Knife Bolts (1/2” x 4” x 7 1/4” Knives - 65)
1/2” - 13 NC
70 - 80
95 - 108
“RS” Hydraulic Feedwheel Motor Shaft Nut (6) /” - 8 NEF
10 - 170
0 - 0
“RE” Hydraulic Feedwheel Motor Shaft Nut (9) 1” - 0 NEF
0 - 00
9 - 07
Engine Sheave Bushing “SD”
1/” - 0 NC
9
1
Engine Sheave Bushing “SK”
/16” - 18 NC
1
0
Engine Sheave Bushing “SF”
/8” - 16 NC
0
1
Chipper Sheave Bushing “E”
1/” - 1 NC
60
81
Chipper Sheave Bushing “F”
9/16” - 1 NC
7
10
Autofeed Cartridge Nut
- 6
- 8
Autofeed Plus Solenoid Retainer Nut
- 6
- 8
Hitch Mount Bolts
/8” - 11 NC
0
98
Chip Box Turntable Bearing
1/2” - 13 NC
65 - 75
88 - 102
