background image

PARTS TO BE INSTALLED

tsi2012-007-007_a

MIRROR PIVOT TOWARDS THE REAR

8. From outside of vehicle, insert a M6 X 45 Torx

screw and secure with a cap nut to hold tem-
porarily the mirror bushing in place.

9. Install the second M6 X 45 Torx screw with a

flat washer and a cap nut.

TORQUE

M6 cap nut

6 N•m (53 lbf•

in

)

tsi2012-007-006

TIGHTEN RETAINING SCREW

10. Adjust mirror angle.

tsi2012-007-001_a

LH SIDE MIRROR INSTALLED

11. Torque nut, inside mirror bushing, to specifica-

tion.

TORQUE

Mirror bushing nut

15 N•m (133 lbf•

in

)

Central Mirror

1. Install the U bracket in center of the front

transversal cage tube.

2. Install the central mirror.

3. Secure them using M6 x 45 Torx screws, M6

flat washers and M6 cap nuts.

4. Tighten cap nuts.

PART

TORQUE

M6 cap nut

10 N•m (89 lbf•

in

)

Mudguards (CE Models Only)

A kit of mudguard is delivered with the vehicle.
This kit may be installed or not in accordance with
owner preferences.

Install mudguard kit as per their installation in-
structions (included in the bag).

Accessories Installation

1. Install accessories (if any) as per their installa-

tion instructions (included in each kit).

2. Install any other equipment required by law (if

any).

Vehicle Decals

1. Install decals on vehicle according to customer

country language and local legislation.

PREDELIVERY

2014-2

33 / 54

Summary of Contents for Can-Am Commander 1000 DPS 2014























































Reviews: