BRONKHORST Mini CORI-FLOW MI Series Page 36 Instruction Manual Download

Page: 36 / 53

Bronkhorst®

Instruction Manual MI Series Industrial mini CORI-FLOW™

9.17.120A

Fieldbus 1 Address

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char



0…255

199

125/10

0x0FAA/4011

Fieldbus 1 Baud Rate

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned long



0…1.0E10

201

125/9

0xFD48…0xFD49/64841…64842

Fieldbus 1 Parity

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char



0…2

335

125/12

0x0FAC/4013

The following values are supported:

Value

Description

No parity

Odd parity

Even parity

4.5

Fluid set

Fluid Set Index

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

0…7

1/16

0x0030/49

With this parameter, any of the pre-configured fluids (up to 8) can be selected. Each fluid has its specific (configurable)

properties, such as

Fluid Name

Capacity

, etc.

Default value: 0 (fluid 1).

Fluid Name

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char[10]



1/17

0x8188…0x818C/33161…33165

This parameter contains the name of the current fluid.

Capacity

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Float



1E-10…

1E+10

1/13

0x8168…0x8169/33129…33130

This parameter sets the maximum readout/control value (100%) for the current fluid in readout units corresponding to

Capacity Unit

Capacity Unit

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char[7]



see below

129

1/31

0x81F8…0x81FB/33273…33276

Summary of Contents for Mini CORI-FLOW MI Series






















































Search results

Summary of Contents for Mini CORI-FLOW MI Series

Reviews:

Related manuals for Mini CORI-FLOW MI Series

Brands by name

Popular brands

BRONKHORST Mini CORI-FLOW MI Series, Instruction Manual

Search results

Summary of Contents for Mini CORI-FLOW MI Series

Reviews:

Related manuals for Mini CORI-FLOW MI Series

Brands by name

Popular brands