BRONKHORST Mini CORI-FLOW MI Series Page 30 Instruction Manual Download

Page: 30 / 53

Bronkhorst®

Instruction Manual MI Series Industrial mini CORI-FLOW™

9.17.120A

4.1

Measurement and control

Measure

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned int

0…41942

(65535*)

1/0

0x0020/33

This parameter indicates the flow metered by the instrument. The value of 32000 corresponds to 100%, the maximum

measured value output is 131.07%, which translates to 41942.

*In case the instrument is prepared for bi-directional measurement, the negative signals with an output range of -

73.73…-0.003% are represented by the range of 41943…65535, whereas the positive signals 0…131.07% are still

represented by the range of 0…41942. (FlowDDE converts the numbers to negative values automatically).

Setpoint

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned int

0…32000

1/1

0x0021/34

This parameter is used to set the required flow rate for the controller. The signals have the same range as

Measure

, but the

setpoint range is limited between 0 and 100% (0…32000).

Temperature

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Float

-250…500

142

33/7

0xA138…0xA139/41273…41274

This parameter returns an indication of the actual media temperature in °C.

Pressure

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Float

0…3.4E+38

143

33/8

0xA140…0xA141/41281…41282

This parameter returns an indication of the actual (inlet) pressure in bar(a). By default the value of this parameter is equal to

parameter

Inlet pressure

Density Actual

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Float

0…3.4E+38

270

116/15

0xF400…0xF401/62465…62466

This parameter returns the actual density measured by the instrument. If the selected

Capacity Unit

is a volume flow type,

the instrument uses this parameter for conversion of the measured mass flow to the selected unit.

4.1.1

Advanced measurement and control

Fmeasure

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Float

-3.4E+38…

3.4E+38

205

33/0

0xA100…0xA101/ 41217…41218

Floating point variant of

Measure

Fmeasure

shows the measured value in the capacity unit for which the instrument is set.

The instrument uses parameters

Capacity

Capacity 0%

Capacity Unit

and

Sensor Type

to calculate

Fmeasure

Summary of Contents for Mini CORI-FLOW MI Series






















































Search results

Summary of Contents for Mini CORI-FLOW MI Series

Reviews:

Related manuals for Mini CORI-FLOW MI Series

Brands by name

Popular brands

BRONKHORST Mini CORI-FLOW MI Series, Instruction Manual

Search results

Summary of Contents for Mini CORI-FLOW MI Series

Reviews:

Related manuals for Mini CORI-FLOW MI Series

Brands by name

Popular brands