BRONKHORST Mini CORI-FLOW MI Series Page 32 Instruction Manual Download

Page: 32 / 53

Bronkhorst®

Instruction Manual MI Series Industrial mini CORI-FLOW™

9.17.120A

4.2

Alarms

Alarm settings are most easily accessible using FlowPlot or FlowView or a Bronkhorst® readout and control unit.

The built-in alarm functionality can be used to handle different alarm types:

system errors and warnings

min/max alarms

response alarms

batch alarms

master/slave alarms

The used alarm type can be set with parameter

Alarm Mode

. When an alarm is activated, the type can be read out using

parameter

Alarm Info

. An automatic setpoint change can be set using the parameters

Alarm Setpoint Mode

and

Alarm New

Setpoint

. It is also possible to set an alarm delay, to prevent overreaction to small disturbances, using parameter

Alarm Delay

Time

. The methods by which an alarm can be reset are controlled by

Reset Alarm Enable

Alarm Mode

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

0…3

118

97/3

0x0C23/3108

Available modes:

Value

Description

Alarm off

Alarm on absolute limits

Alarm on limits related to setpoint (response alarm)

Alarm at power-up(e.g. after power-down)

(For DeviceNet™ instruments, only modes 0 and 1 are available)

Alarm Info

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

0…255

1/20

0x0034/53

This parameter provides information about the event type(s) that triggered an alarm situation. The value is a bit-wise

summation of the issued alarm types; convert the value to binary to see which types are issued. The following alarm types

can be issued:

Bit

Value

Type

Description

Error

Error flag raised

Warning

Warning flag raised

Minimum alarm

Measure

Alarm minimum limit

Maximum alarm

Measure

Alarm maximum limit

Batch counter alarm

Batch counter reached its limit

This bit only: Power-up alarm

Alarm possibly caused by a power dip

If combined with bit 2 or 3:

Response alarm

Difference between

Measure

and

Setpoint

too big

Master/slave alarm

Setpoint out of limits (caused by

Slave factor

)

128

Hardware alarm

Hardware error

Alarm Delay Time

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

0…255

182

97/7

0x0C27/3112

This value represents the time in seconds the alarm action will be delayed when an alarm limit has been exceeded. This

value also delays the alarm off action if an alarm limit is no longer exceeded.

Default value = '0'.

Summary of Contents for Mini CORI-FLOW MI Series






















































Search results

Summary of Contents for Mini CORI-FLOW MI Series

Reviews:

Related manuals for Mini CORI-FLOW MI Series

Brands by name

Popular brands

BRONKHORST Mini CORI-FLOW MI Series, Instruction Manual

Search results

Summary of Contents for Mini CORI-FLOW MI Series

Reviews:

Related manuals for Mini CORI-FLOW MI Series

Brands by name

Popular brands