BRONKHORST Mini CORI-FLOW MI Series Instruction Manual Download Page 22

Page: 22 / 53

Bronkhorst®

Instruction Manual MI Series Industrial mini CORI-FLOW™

9.17.120A

•

Error

Pattern

Time

Indication

off

continuous

No error

continuous

Critical error; the instrument needs servicing before it can be used

short flash

0.1 sec on,

2 sec off

FLOW-BUS

Node occupied: re-install instrument

PROFIBUS DP

No data exchange between master and slave (automatic recovery)

Modbus

Data is being received or transmitted

EtherCAT®

Instrument is not in OP mode

PROFINET

No application relation established

blink

0.2 sec on,

0.2 sec off

FLOW-BUS

Waiting for communication, check communication settings of all

FLOW-BUS devices in the fieldbus setup. Usually the ‘last node

address’ setting of one of the devices is incorrect.

PROFIBUS DP

Not used

Modbus

Not used

EtherCAT®

Not used

PROFINET

Not used

long flash

2 sec on,

0.1 sec off

FLOW-BUS

Not used

PROFIBUS DP

Requested parameter not available

Modbus

Not used

EtherCAT®

Configuration error

PROFINET

Configuration error (e.g. a requested parameter is not available)

•

Mode and

•

Error (alternating)

Pattern

Time

Indication

slow wink

1 sec on,

1 sec off

Alarm indication; minimum/maximum alarm, power-up alarm, limit reached or batch

size reached

normal wink

0.2 sec on,

0.2 sec off

Wink mode; by sending a command to the

Wink

parameter, the instrument flashes its

LEDs to indicate its position in a (large) system.

fast wink

0.1 sec on,

0.1 sec off

Selected action started (after releasing the multifunctional switch)

3.7.1.1

Interface status

The Status LED is only used for Ethernet based fieldbus types (i.e. EtherCAT® and PROFINET).

Summary of Contents for Mini CORI-FLOW MI Series






















































Search results

Summary of Contents for Mini CORI-FLOW MI Series

Reviews:

Related manuals for Mini CORI-FLOW MI Series

Brands by name

Popular brands

BRONKHORST Mini CORI-FLOW MI Series, Instruction Manual

Search results

Summary of Contents for Mini CORI-FLOW MI Series

Reviews:

Related manuals for Mini CORI-FLOW MI Series

Brands by name

Popular brands