manualshive.com logo in svg

BRONKHORST Mini CORI-FLOW MI Series, Instruction Manual, Page: 20 / 53

Share
Download
BRONKHORST Mini CORI-FLOW MI Series Instruction Manual Download Page 20

Bronkhorst®

Instruction Manual MI Series Industrial mini CORI-FLOW™

9.17.120A

20

PROFIBUS-DP

Instruments in a PROFIBUS DP system can be monitored and operated using third party software as a master device, such as

TIA Portal (by Siemens).

To configure a device, a so-called GSD file (General Station Description) can be loaded into the software. The GSD file

contains all necessary configuration information to operate the device in a PROFIBUS DP system, including communication

and network configuration, and all available operating parameters with their data types.

A GSD file for Bronkhorst® instruments can be downloaded from the product pages on the Bronkhorst website: 

www.bronkhorst.com/products

PROFINET

Instruments in a PROFINET system can be monitored and operated using third party software as a master device, such as TIA

Portal (by Siemens).

To configure a device, a so-called GSDML file (General Station Description Markup Language) can be loaded into the

software. The GSDML file contains all necessary information, in XML format, to operate the device in a PROFINET system,

including communication and network configuration, and all available operating parameters with their data types.

A GSDML file for Bronkhorst® instruments can be downloaded from the product pages on the Bronkhorst website: 

www.bronkhorst.com/products

EtherCAT®

Instruments in an EtherCAT® system can be monitored and operated using third party software as a master device, such as

SyCon® (by Hilscher GmbH).

To configure a device, a so-called ESI file (EtherCAT® Slave Information) can be loaded into the software. The ESI file contains

all necessary configuration information to operate the device in a EtherCAT® system, including communication and network

configuration, and all available operating parameters with their data types.

An ESI file for Bronkhorst® instruments can be downloaded from the product pages on the Bronkhorst website: 

www.bronkhorst.com/products

HART

Monitoring and operating instruments in a HART system can be done using third party software as a master device.

To configure a device, a so-called DD file (Device Description) can be loaded into the software. The DD file contains all

necessary configuration information to operate the device in a HART system, including communication and network

configuration, and all available operating parameters with their data types.

Because the HART protocol uses the analog output line of the instrument, it can be combined with any of the other

interfaces (analog and digital). It can even be monitored and operated simultaneously with another fieldbus interface,

however, when writing values to the same parameter from two digital interfaces, the last interface to send a value prevails.

Summary of Contents for Mini CORI-FLOW MI Series






















































Reviews:

No comments