BRONKHORST Mini CORI-FLOW MI Series Page 41 Instruction Manual Download

Page: 41 / 53

Bronkhorst®

Instruction Manual MI Series Industrial mini CORI-FLOW™

9.17.120A

Firmware Version

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char[6]

105

113/5

0xF128…0xF12A/ 61737…61739

Revision number of the firmware

Identification Number

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char



0…255

175

113/12

0x0E2C/3629

Bronkhorst® (digital) device type identification number.

Device Type

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char[6]

113/1

0xF108…0xF10A/ 61705…61707

Device type information string; this parameter contains an abbreviation referring to the identification number.

4.9

Special parameters

Init Reset

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

82/64

0/10

0x000A/11

Init Reset

is used to unlock secured parameters (marked with a



symbol) for writing. It supports the following values:

Value

Description

unlocked, secured parameters can be read and written to

locked, secured parameters are read-only

At power-up,

Init Reset

is always set to ‘Locked’ (value 82).

Reset

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

0…7

114

115/8

0x0E68/3689

This parameter is used to reset the program, counter or alarms.

Value

Description

No reset

Reset counter

Reset alarm

Reset counter

Reset and disable counter

Reset firmware program (soft reset)

Reset

Alarm info

error bit

Reset

Alarm info

warning bit

The

Reset

parameter may be disabled by

Reset Alarm Enable

Reset Counter Enable

. Make sure the value is accepted

by sending value 0 first.

Summary of Contents for Mini CORI-FLOW MI Series






















































Search results

Summary of Contents for Mini CORI-FLOW MI Series

Reviews:

Related manuals for Mini CORI-FLOW MI Series

Brands by name

Popular brands

BRONKHORST Mini CORI-FLOW MI Series, Instruction Manual

Search results

Summary of Contents for Mini CORI-FLOW MI Series

Reviews:

Related manuals for Mini CORI-FLOW MI Series

Brands by name

Popular brands