BRONKHORST Mini CORI-FLOW MI Series Instruction Manual Download Page 43

Page: 43 / 53

Bronkhorst®

Instruction Manual MI Series Industrial mini CORI-FLOW™

9.17.120A

Changing from digital operation to analog operation:

1. Set parameter

Init Reset

to 64 (unlocked)

2. Read parameter

IO Status

3. Add 64 to the read value

4. Write the new value to parameter

IO Status

5. Set parameter

Init Reset

to 82 (locked)

Changing from analog operation to digital operation:

1. Set parameter

Init Reset

to 64 (unlocked)

2. Read parameter

IO Status

3. Subtract 64 from the read value

4. Write the new value to parameter

IO Status

5. Set parameter

Init Reset

to 82 (locked)

The procedures described above do not change the value of parameter

Control Mode

directly. To apply the new default

control mode immediately, change the value of parameter

Control Mode

manually or reset or restart the instrument.

Summary of Contents for Mini CORI-FLOW MI Series






















































Search results

Summary of Contents for Mini CORI-FLOW MI Series

Reviews:

Related manuals for Mini CORI-FLOW MI Series

Brands by name

Popular brands

BRONKHORST Mini CORI-FLOW MI Series, Instruction Manual

Search results

Summary of Contents for Mini CORI-FLOW MI Series

Reviews:

Related manuals for Mini CORI-FLOW MI Series

Brands by name

Popular brands