manualshive.com logo in svg

BRADEN CH330, Installation Maintenance And Service Manual, Page: 3 / 36

Share
Download
BRADEN CH330 Installation Maintenance And Service Manual Download Page 3

3

TABLE OF CONTENTS

Foreword .....................................................................................................................4

Model and Serial Number Location .............................................................................4

Explanation of Model Number .....................................................................................4

General Safety Recommendations..............................................................................5

Theory of Operation.....................................................................................................6

Winch and Wire Rope Installation ...............................................................................8

3-piece Cable Anchor Installation (Model CH400).......................................................9

Hydraulic Circuits.......................................................................................................10

Preventive Maintenance ............................................................................................ 11

Weights, Oil Capacities, and Special Tools ...............................................................13

Troubleshooting .........................................................................................................14

Service Precautions...................................................................................................17

Winch Disassembly ...................................................................................................17

Drum Support End Bracket Service...........................................................................18

Exploded-view Drawing .............................................................................................19

Parts List....................................................................................................................20

Winch Drive/Gearbox Service ...................................................................................21

Subassembly Service ................................................................................................22

Brake Assembly Service ............................................................................................23

Planet Carrier Service ...............................................................................................26

Winch Assembly ........................................................................................................28  

Brake Valve Service ..................................................................................................32

Recommended Fastener Torque ...............................................................................35

Metric Conversion Chart ............................................................................................36

Summary of Contents for CH330





































Reviews:

No comments