Bosch VG5 600 Series Installation Manual Download

Page: 70 / 88

en | Cable and Wire Standards

AutoDome 600 Series Analog PTZ Camera

F.01U.265.793 | 2.0 | 2012.02

Installation Manual

Bosch Security Systems, Inc.

The figure below illustrates the connections necessary for Biphase operation.

Figure 5.2

Connections for Biphase Operation

In a daisy chain configuration, where multiple domes are connected in series, the 100 Ω

resistor must be removed from all but the last dome. You can daisy chain a maximum of four

(4) AutoDomes.

Figure 5.3

Connections for a Daisy Chain Configuration

C- (Biphase)

AutoDome Data In/Out

C+ (Biphase)

Head End Biphase

Earth Ground

P105/P106 Connector

RxD

C- (Biphase)

TxD

C+ (Biphase)

Signal Ground

Shield

C- (Biphase)

Dome 3

C+ (Biphase)

Dome 2

Earth Ground

Dome 1

RxD

Head End Biphase

TxD

C- (Biphase)

Signal Ground

C + (Biphase)

Last Dome Data In/Out

Shield

P105/P106 Connector

100

Summary of Contents for VG5 600 Series

























































































Search results

Summary of Contents for VG5 600 Series

Reviews:

Related manuals for VG5 600 Series

Brands by name

Popular brands

Bosch VG5 600 Series, Installation Manual

Search results

Summary of Contents for VG5 600 Series

Reviews:

Related manuals for VG5 600 Series

Brands by name

Popular brands