Bosch VG5 600 Series Installation Manual Download

Page: 26 / 88

en | Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts

AutoDome 600 Series Analog PTZ Camera

F.01U.265.793 | 2.0 | 2012.02

Installation Manual

Bosch Security Systems, Inc.

2.7

Make Connections in Power Supply Box

Refer to

Table 2.2, Page 22

to locate the various connectors in the power supply box and make

the following connections detailed below.

Figure 2.11

Pendant Arm connections to Power Supply Box

Attach the earth ground wire (item 1 in the illustration above) to the grounding screw on

the left side of the power box.

Connect the 6-pin Control In/Out Plug, installed previously, to its mating connector P106

in the power box. If this product is a Fiber Optic model this step is not required, since all

control data is sent through the fiber cable.

Connect the 6-pin Control to Dome Plug from the Pendant Connector Harness to its

matting connector P105 in the power box. (For Fiber Optic model connect to the P106

connector.)

Control Data

Coax Video

24 VAC Power

UTP Video/Ethernet

(Ethernet for VG5 700 Series only)

Alarm Inputs

Alarm Outputs

Relays

Grounding Strap

1 2 3

WARNING!

Do not connect the RJ45 connector unless using UTP video or Ethernet.

Summary of Contents for VG5 600 Series

























































































Search results

Summary of Contents for VG5 600 Series

Reviews:

Related manuals for VG5 600 Series

Brands by name

Popular brands

Bosch VG5 600 Series, Installation Manual

Search results

Summary of Contents for VG5 600 Series

Reviews:

Related manuals for VG5 600 Series

Brands by name

Popular brands