Bosch SHP65TL5UC Repair Instructions Download

Page: 70 / 82

702_58300000170749_ara_en_c

Page 70 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

Error
Code

Description

Part

DW Symptoms

(seen during wash cycles)

Solution

Extra Dry Heat

option hasn't

been turned on

Activate

Extra Dry Hea

t option, if it's not activated and is

available on the dishwasher.

Clogged spray arms or filters.

Washability issue (heat pump runs, but dishes still
dirty)

Remove debris / obstructions from filter and spray arms.

Spray arms not rotating

Make sure spray arms are properly attached and rotate
freely.

Make sure spray arms are properly aligned with the supply
tube.

Door is ajar

Dishwasher won’t start

Educate customer on closing door securely.

Summary of Contents for SHP65TL5UC



















































































Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands

Bosch SHP65TL5UC, Repair Instructions

Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands