Bosch SHP65TL5UC Repair Instructions Download

Page: 41 / 82

702_58300000170749_ara_en_c

Page 41 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

TIP

: When replacing an inner door – dishwashers

cannot

be identified since their serial labels are attached to the
inner doors being replaced:

1. Have customers write their model and serial #’s in their

Use & Care manuals.

2. Legibly write the model and serial #’s on the ss surface

(near the bitumen at the dispenser) of the replacement
inner door using a fine tip black permanent marker.

5.1.4.7 To remove lower door seal

The lower door seal is
attached by two of the four
inner door screws. It is
removed along with the inner
door.

Tools needed: T20 Torx & #2 Phillips screwdrivers, pliers &
gloves

Remove inner door

– section 5.11. The lower door seal

will be loose since it’s two (2) screws were removed when
the inner door was removed

(below left)

. If the seal sticks

to the inner door, separate the seal from the door by hand

(below left)

2. Remove lower door seal

(below right)

CAUTION:

Inner door edges (at the hinge) are sharp! Use

gloves, cover inner door edges and remove lower door
seal carefully.

5.1.5

Pulling out dishwashers

Follow these instructions to pull out dishwashers for side or
bottom front access.

5.1.5.1 Disconnect & pull out dishwasher

Tools needed: #2 Phillips screwdriver and pliers or wrench.

1. Remove base insulation (on models with insulation).

Summary of Contents for SHP65TL5UC



















































































Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands

Bosch SHP65TL5UC, Repair Instructions

Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands