Bosch SHP65TL5UC Repair Instructions Download

Page: 67 / 82

702_58300000170749_ara_en_c

Page 67 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

Error
Code

Description

Part

DW Symptoms

(seen during wash cycles)

Solution

E:11

NTC or NTC wiring harness
error

C’

(

t p

)

Not heating

Check continuity between NTC’s and power module.

Measure NTC resistances

, which should be ≈ 10 kΩ

between terminals 4-5 & 5-6

and ≈ 20 kΩ between

terminals 4-6 @ room temp. If not, replace heat pump. If
so, replace power module.

E:13

Incoming

water too hot (> 75ºC

/ 167ºF)

Dishwasher runs without heat pump heating
element running

Make sure water inlet temp is < 75ºC / 167ºF.

E:15

Float switch activated and
dishwasher runs continually /
can’t be turned off

t s

itc

Water doesn't fill and drain pump runs continually

Remove debris / obstructions from drain pump / drain hose.
Remove water from base.

Make sure float & float switch aren't stuck.

Make sure water inlet valve isn't stuck "open".

Check float switch and wire harness (to power module).

E:17

Faulty water softener
regeneration valve

Water softener doesn’t regenerate

Check continuity between regeneration valve

(k1)

and

power module.

E:20

Faulty heat pump motor
winding

eat

Wash cycle abruptly ends with

Clean

Sanitized

LED’s lit

Check continuity between heat pump

(m2)

and power

module.

Measure heat pump resistance between any 2 terminals. If

≈ 15.2 Ω @ room temp, replace power module. If not,
replace heat pump.

E:21

Heat pump is blocked / clogged

Remove debris / obstructions from heat pump.

If pump impeller is stuck, replace heat pump.

Summary of Contents for SHP65TL5UC



















































































Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands

Bosch SHP65TL5UC, Repair Instructions

Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands