Bosch SHP65TL5UC Repair Instructions Download

Page: 61 / 82

702_58300000170749_ara_en_c

Page 61 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

CAUTION:

Take care to not lose the regeneration

valve spring when removing the valve coil or body.

4. To remove the valve body, place a small blade screwdriver

into it and carefully pry it out from the softener

(below)

5.19.2

Assembling regeneration valve

When assembling / reassembling the regeneration valve, line up
the marks on the valve body and coil

(below)

. When the marks

are aligned, carefully press the body with spring into the coil until
the parts come together.

CAUTION:

The regeneration valve body, spring and coil

must be properly reassembled to avoid damage.

5.19.3

Removing water softener

Tools needed: #2 Phillips & small flat blade screwdrivers, along
with special tool part # 341805.

Flip dishwasher for bottom access

– section 5.1.6.1.

2. Disconnect regeneration valve wire harness

(below)

Summary of Contents for SHP65TL5UC



















































































Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands

Bosch SHP65TL5UC, Repair Instructions

Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands