Bosch SHP65TL5UC Repair Instructions Download

Page: 55 / 82

702_58300000170749_ara_en_c

Page 55 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

2. Remove hose clamp to separate pump from adapter

(below)

3. Disconnect support strap

(below)

4. To remove pump, slide pump off sump at seal ring. The

seal ring

can’t

be field removed from the heat pump.

5. Disconnect the two (2) pump wire harnesses

(below left)

To remove the small connector for the sensor harness with
black wires, unlatch it from it’s terminal

(below center)

6. If necessary, remove the adapter by removing four (4)

screws

(below right)

TIP

: The replacement heat pump comes with motor, pump,

seal ring and hose clamp.

NOTE:

The motor can’t be separated from the pump and

the seal ring can’t be field installed.

Summary of Contents for SHP65TL5UC



















































































Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands

Bosch SHP65TL5UC, Repair Instructions

Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands