Bosch SHP65TL5UC Repair Instructions Download

Page: 66 / 82

702_58300000170749_ara_en_c

Page 66 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

6.1.4

Error code / troubleshooting chart

Error
Code

Description

Part

DW Symptoms

(seen during wash cycles)

Solution

E:00

No errors

E:01

Faulty pump relay

r m

Wash cycle abruptly ends with

Sanitized

LED lit

Replace power module (located in base).

E:02

Faulty heater relay

Dishwasher runs without heating / heater error

E:05

Faulty water switch relay

Water switch runs continually

E:06

Door latch Hall sensor not
detected

l sen

DW won’t run &

Clean

LED is flashing

Align door latch above Hall sensor

(inside inner door)

Defective door latch Hall sensor

Check continuity / connections between door switch

(q2)

and power module.

With door closed, measure voltage across door latch Hall
sensor connector. If > 10V, replace Hall sensor. If < 10 V,
replace power module.

E:08

Heat pump detects low water
level

let

Not heating

Check water supply & repair any leaks. Check for kinks in
inlet hoses. Turn over pots / bowls collecting water.

Check continuity between water inlet valve

(k2)

and power

module.

Measure voltage across water inlet valve terminals

(k2)

during step 1 of customer service test program. If ≈ 120V,

replace water inlet valve. If not ≈ 120V, replace power
module.

E:09

Faulty heater circuit (open -
circuited)

eat

Check continuity between heat pump heating element

(e1)

and power module.

Measure heat pump heating element

(e1)

resistance, which

should be ≈ 8.9Ω @ room temp. If not, replace heat pump.
If so, replace power module.

Summary of Contents for SHP65TL5UC



















































































Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands

Bosch SHP65TL5UC, Repair Instructions

Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands