manualshive.com logo in svg

Bosch Rexroth Servodyn-D Series, Maintenance Manuallines, Page: 53 / 74

Share
Download
Bosch Rexroth Servodyn-D Series Maintenance Manuallines Download Page 53

4–30

Electric Drives

and Controls

Bosch Rexroth AG

Servodyn-D 1070 066 032 / 03

Servodyn-D frequency inverter displays

Read

from 

DSS

Unit Description

A00 A-0-1000 Hz Actual output frequency

f

act

Current motor frequency

A01 A-0-1001 Hz Commanded output fre-

quency f

set

Specified output frequency

A02 A-0-1002

A

Total current

rms value of the total current

A03 A-0-1003

A

Active current

rms value of active current

A04 A-0-1004

A

Reactive current

rms value of reactive current

A05 A-0-1005

V

Motor voltage

rms value of current motor voltage

A06 A-0-1006

V

DC link voltage

Current value of DC link voltage

(display = 350 V for voltage values 

x

 350 V)

A07 A-0-1007 kVA Total power

Current total power

A08 A-0-1008 kW Shaft output

Current mechanical shaft output of the motor

A09 A-0-1009

%

Utilization

Current utilization of the motor,

for f < f

N

 with reference to the motor torque M

N

for f > f

N

 with reference to the motor power P

N

Accuracy:

depends on the motor, 

for n > 0.1 n

N

 approx. 5% of the final value

A10 A-0-1010

_

C Heat sink temperature

Current heat sink temperature. 

With increased heat sink temperature: Warning ‘U01’, 

TEMP relay is opened.

A11 A-0-1011

A

Present current limit

The presently effective current limit is set depending on the

selected settings and the current heat sink temperature.

A12 A-0-1012

TEMP warning

Warning message 

when TEMP relay has switched off:

U00

no warning

U01

excessive heat sink temperature

U02

Excessive motor temperature.

Only if bimetal function is active P43 – P45.

U03

Excessive heat sink and motor temperature

A13 A-0-1013

Last error after 

STA shut-off

After restart, the last error present before STA was deacti-

vated is displayed.

A14 A-0-1014

Software version

Number left of point = software status

Number right of point = software scope.
Please indicate this data in the event of enquiries.

A15 A-0-1015

Software index

Version index of operating software, 

always specify in enquiries.

Summary of Contents for Rexroth Servodyn-D Series











































































Reviews:

No comments