manualshive.com logo in svg

Bosch Rexroth Servodyn-D Series, Maintenance Manuallines, Page: 11 / 74

Share
Download
Bosch Rexroth Servodyn-D Series Maintenance Manuallines Download Page 11

1–6

Electric Drives

and Controls

Bosch Rexroth AG

Servodyn-D 1070 066 032 / 03

Safety Instructions

1.5

Safety instructions for the described product

DANGER

Danger of life through inadequate EMERGENCY-STOP devices!

EMERGENCY-STOP devices must be active and within reach in all

system modes. Releasing an EMERGENCY-STOP device must not

result in an uncontrolled restart of the system! 

First check the EMERGENCY-STOP circuit, then switch the sys-

tem on!

DANGER

Danger for persons and equipment!

Test every new program before starting up a system!

DANGER

Retrofits or modifications may adversely affect the safety of the

products described!

The consequences may include severe injury, damage to equip-

ment, or environmental hazards. Possible retrofits or modifica-

tions to the system using third-party equipment therefore have to

be approved by Rexroth.

DANGER

Health hazards through destroyed electrical components!

Do not destroy any built-in components. Dispose of destroyed

components in a proper manner.

DANGER

Do not look directly into the LEDs in the optical fiber connection.

Due to their high output, this may result in eye injuries.

When the inverter is switched on, do not look into the LED or the

open end of a short connected lead.

DANGER

Please note your local, system-specific regulations and require-

ments as well as the proper use of tools, hoisting and transport

equipment as well as the applicable standards, regulations, and

accident prevention regulations.

Summary of Contents for Rexroth Servodyn-D Series











































































Reviews:

No comments