Bosch Rexroth Servodyn-D Series Maintenance Manuallines Download Page 32

Page: 32 / 74

Electric Drives

and Controls

4–9

Bosch Rexroth AG

Servodyn-D

1070 066 032 / 03

VMA..KR, VMA..B,C,D,F and DM/DS error displays

Displays flash

alternately.

Action

Error

The drive has switched off.

Drives do not stand still

Drives shutdown not completed when time

limit has expired

Check time limit setting in VM

Check enable signals

Clear error with “Drive On”

Channel error Emergency-Stop

None of the channels was not switched

within 0.5 sec

Check Emergency-Stop wiring

(X312.2, X06.3/4)

Clear error by activating the Emergency

Stop channel again, then unlocking

Emergency Stop channel, then output-

ting “Drive On”.

Channel error operating mode (RSU)

Operating mode switchover via channels

NO and SO does not take place within 2

sec.

Check control of the VM inputs NO and

SO (X312.3/4, X06.6)

Check safety door tumbler control

Clear error with “Drive On”

Channel error safety door tumbler

(RSU)

The check-back signal “safety door re-

leased” was not given within approx. 2 sec.

in special mode

Check safety door tumbler

Check PLC check-back signal (X312.6)

The VM should be replaced if there is a

short-circuit in the driver of the safety

door release (X312.5)

Clear error with “Drive On”

Normal operating mode:

Output stage cannot be switched off

Special mode (RSU):

Channel error Acknowledgement

The two acknowledgement channels

have not been activated simultaneously

(P-0-0024)

Time limit P-0-0023 for acknowledge-

ment exceeded

Channel error “Safe signal transmis-

sion”

Defective signal transmission in X810 start-

ing with module with this error message

Channel error “Safety-oriented data”

The cyclic safety-oriented data on the PM

module and in the EEPROM are not identi-

cal

For details of the fault, refer to

S-0-0095, cf. page 4–14.

Clear error on the DMs by “Reset Diag-

nostics class 1 error”, on the VM with

“RESET”

Replace module

Check wiring (X312.1, X06.5)

Check key for mechanical or electrical

bridge

Observe sequence of operations

Check X810 signal cross-connection

Replace module

Check safety-oriented data

Clear error by “Reset Diagnostics class

1 error”

Channel error FGZ (RSU)

Defective transmission of the central en-

able signal from VM

Check X810 signal cross-connection

Replace module

Summary of Contents for Rexroth Servodyn-D Series











































































Search results

Summary of Contents for Rexroth Servodyn-D Series

Reviews:

Bosch Rexroth Servodyn-D Series, Maintenance Manuallines, Page: 32 / 74

Search results

Summary of Contents for Rexroth Servodyn-D Series

Reviews: