Bosch Rexroth Servodyn-D Series Maintenance Manuallines Download Page 51

Page: 51 / 74

4–28

Electric Drives

and Controls

Bosch Rexroth AG

Servodyn-D 1070 066 032 / 03

PROFIBUS-DP errors

4.6

PROFIBUS-DP errors

Displays flash

alternately.

Error

The drive has switched off.

Action

Initialization error

Incorrect parameterization data

Check structure of the parameterization

data

(refer to “Servodyn with PROFIBUS-DP

Interface” manual)

Initialization error

Configuration data does not match the de-

sired configuration

Check whether the drive mode from the

parameterization data matches the tele-

gram configuration

4.7

DMA computer errors (without SERCOS interface)

Displays flash

alternately.

Error

The drive has switched off.

Action

up to

CPU program execution errors

H01 dc Power failure (also refer to F 36)

H02 stack overflow

H03 stack

underflow

H04 undefined CPU code

H05 undefined protected command

H06 inadmissible word instruction

H07 inadmissible jump

H08 inadmissible bus control

Contact Rexroth technical service

Replace module

up to

CPU computing errors

H09 integer overflow

H10 floating overflow

H11 floating underflow

H12 division by zero

H13 undefined floating number

H14 integer/floating conversion error

H15 floating point stack overflow

H16 floating point stack underflow

Check last parameter changes made

before error occurred

Contact Rexroth technical service

Summary of Contents for Rexroth Servodyn-D Series











































































Search results

Summary of Contents for Rexroth Servodyn-D Series

Reviews:

Bosch Rexroth Servodyn-D Series, Maintenance Manuallines, Page: 51 / 74

Search results

Summary of Contents for Rexroth Servodyn-D Series

Reviews: