Bosch Rexroth Servodyn-D Series Maintenance Manuallines Download Page 52

Page: 52 / 74

Electric Drives

and Controls

4–29

Bosch Rexroth AG

Servodyn-D

1070 066 032 / 03

Servodyn-D frequency inverter displays

4.8

Servodyn-D frequency inverter displays

4.8.1

Status/warning displays

LED

Status

Action

Axis enable external

24 V at X06.3/4 (FG)

–

FGI

Enable internal

24 V at X06.3 (FG)

Central enable by VM present

no error

–

3-digit 7-segment display

computer has

been booted
TEMP
STA

Operating display:

STA is present if:

– computer has been booted

– no errors

Temperature status:

TEMP is present if:

Temperature of the heat sink or the

motor (with active bimetal function) is

within the permitted range.

TEMP relay is closed

–

If no display (temperature exceeded):

Check air supply, fan

Reduce cycle frequency or load

Select motor with higher rating

Verify bimetal setting

You can read various operating data from the 7-segment display:

Press <D> key in the basic display.

Select the ’A’ display function with the < > or < > keys.

Press key <D>.

Select the desired operating display with the < > or < > keys,

e.g. A00 (actual output frequency).

Press key <D>.

The display shows the current operating data.

Jump back to the operating data level by simultaneously press-

ing the < > and < > keys.

You may now select the next operating display with the < > or

< > keys, e.g. A08.

Further procedure as described above.

Summary of Contents for Rexroth Servodyn-D Series











































































Search results

Summary of Contents for Rexroth Servodyn-D Series

Reviews:

Bosch Rexroth Servodyn-D Series, Maintenance Manuallines, Page: 52 / 74

Search results

Summary of Contents for Rexroth Servodyn-D Series

Reviews: