manualshive.com logo in svg

Bosch Rexroth Servodyn-D Series, Maintenance Manuallines, Page: 25 / 74

Share
Download
Bosch Rexroth Servodyn-D Series Maintenance Manuallines Download Page 25

4–2

Electric Drives

and Controls

Bosch Rexroth AG

Servodyn-D 1070 066 032 / 03

VMA..KR, VMA..B,C,D,F status displays

4.2

VMA..KR, VMA..B,C,D,F status displays

LED

Status

Action

AE

Drive On

LED lights up at 24 V at X06.7 (AE)

–

FGI

Enable internal

 if

D

24 V at X06.7 (AE)

D

no error

–

Multi-digit displays flash 

alternately.

Normal operation (NO)

Standard ready display

–

Special operating mode (SO)

Operating mode for open safety door where

standstill monitoring of the drives is still active

at maximum energy supply.

–

Intermediate circuit not yet discharged

Alternate flashing while DC link voltage >50 V

Wait for a discharge time of 5 minutes and

then check the DC link at the DC measuring

sockets for zero voltage.

DANGEROUS ELECTRICAL VOLTAGE

Before dismounting the modules, wait for a discharge time of 5

minutes and check the DC link at the DC measuring sockets for

zero voltage.

Summary of Contents for Rexroth Servodyn-D Series











































































Reviews:

No comments