manualshive.com logo in svg

Bosch Rexroth Servodyn-D Series, Maintenance Manuallines, Page: 42 / 74

Share
Download
Bosch Rexroth Servodyn-D Series Maintenance Manuallines Download Page 42

Electric Drives

and Controls

4–19

Bosch Rexroth AG

Servodyn-D

1070 066 032 / 03

VMA..KR, VMA..B,C,D,F and DM/DS error displays

F code

display

Meaning

Error

number

F70

303

Faulty data transfer; Defective motor rating plate

304

Faulty data transfer; Defective motor rating plate

305

I2C bus not addressable (defective cable; loose connection, misc. faults ...)

306

Faulty data transfer; Defective motor rating plate

307

Faulty data transfer; Defective motor rating plate

308

Faulty data transfer; Defective motor rating plate

309

Faulty data transfer; Defective motor rating plate

310

Faulty data transfer; Defective motor rating plate

311

Faulty data transfer; Defective motor rating plate

312

Faulty data transfer; Defective motor rating plate

313

Faulty data transfer  (CRC check, motor rating plate)

314

Faulty data transfer; Defective motor rating plate (checksum test)

315

Faulty data transfer; Defective motor rating plate (checksum test)

316

Faulty data transfer; Defective motor rating plate (checksum test)

317

Faulty data transfer; Defective motor rating plate (checksum test)

318

Missing motor interface; Defective cable;Loose connection;Defective rating plate

319

There is no 2nd parameter set for SSI interface

320

Faulty data transfer; Defective motor rating plate

321

Faulty data transfer  (CRC check, motor rating plate)

322

Unable to clear internal flash memory –> Defective memory location

323

Unable to write to internal flash memory –> Defective memory location

324

Unable to write to internal flash memory –> Defective memory location

325

Defective memory location in internal flash module (checksum test)

326

Defective memory location in internal flash module (checksum test)

329

I2C bus not addressable (defective cable; loose connection, misc. faults ...)

331

I2C bus not addressable (defective cable; loose connection, misc. faults ...)

332

I2C bus not addressable (defective cable; loose connection, misc. faults ...)

333

I2C bus not addressable (defective cable; loose connection, misc. faults ...)

334

I2C bus not addressable (defective cable; loose connection, misc. faults ...)

335

I2C bus not addressable (defective cable; loose connection, misc. faults ...)

1201

Motor rating plate: Parameter set 1: Motor type = 0

1202

Motor rating plate: Parameter set 1: Version number = 0

1203

Motor rating plate: Parameter set 1: Encoder pulses = 0

1204

Motor rating plate: Parameter set 1: Nominal velocity = 0

1205

Motor rating plate: Parameter set 1: Max. velocity = 0

1206

Motor rating plate: Parameter set 1: Nominal current = 0

1207

Motor rating plate: Parameter set 1: Standstill current = 0

1208

Motor rating plate: Parameter set 1: Maximum current = 0

1209

Motor rating plate: Parameter set 1: Rated torque = 0

Summary of Contents for Rexroth Servodyn-D Series











































































Reviews:

No comments