Bosch rexroth HS5E Instruction Manual Download Page 99 | Manualshive

Page: 99 / 104

Bosch rexroth HS5E Instruction Manual Download Page 99

RE 92076-01-B/2021-04-22, Bosch Rexroth AG

Troubleshooting |

A4... with HS5E(V)(L) control system Series 1x and 30 99

/104

Table 28: Malfunction table of HS5E control systems

Malfunction

Possible cause

Remedy

Pressure statically at approx
5...12 bar, cannot be changed

Supply voltage not within the permissible range
Diagnosis: Check the status LEDs

Check, whether the central connector XH4
is connected to the HS5E pilot control valve
Check voltage at the last interconnection
point (terminal strip) upstream the HS5E
pilot control valve

Command value for pressure, swivel angle or
power (optional) is 0 bar or 0%, respectively

If you use, for example, exclusively closed-
loop pressure control, provide a swivel angle
command value of 100%

Swivel angle sensor defective

Check swivel angle measurement,
see chapter 8.1.5.4 on page 73

Piston is stuck in the HS5E pilot control valve

Contact Rexroth Service

Pressure too low

Actual pressure value acquisition incorrectly
configured

Check actual pressure value in IndraWorks
and, if required, correct configuration of
actual pressure value acquisition
Replace pressure transducer, see page 89
Change installation location of the pressure
transducer (do not install upstream of
the preload valve; if possible, close to the
consumer)

Pressure transducer defective/not connected
Diagnosis: Measure signal from PT and compare
with indication on the pressure gauge

Replace pressure transducer, see page 89
Connect pressure transducer

Control system does not work in closed-loop
pressure control

Increase swivel angle command value
Check that the hydraulic system is leak-free
and that the withdrawal is not excessively
high

HS5E pilot control valve faulty

Replace the HS5E pilot control valve,
see chapter 10.5.1 on page 87

Pressure too high

Actual pressure value acquisition incorrectly
configured

Check actual pressure value in IndraWorks
and, if required, correct configuration of
actual pressure value acquisition
Replace pressure transducer, see page 61

Pressure transducer defective/not connected
Diagnosis: Measure signal from PT and compare
with indication on the pressure gauge

Replace pressure transducer, see page 61
Connect pressure transducer

HS5E pilot control valve faulty

Replace the HS5E pilot control valve,
see chapter 10.5.1 on page 87

Insufficient flow

Pressure controller active

Increase pressure command value

Actual swivel angle acquisition improperly set

Recalibrate swivel angle sensor

Rotational speed speed too low (slip, incorrect
frequency, wrong motor)

Contact machine or system manufacturer

Damage to the pump (excessive pump leakage)

Rotary group damaged,
Contact Rexroth Service

Wear/mechanical damage to the control system Replace the control system, contact Rexroth

Service

«
...
97
98
99
100
101
...
»

Summary of Contents for rexroth HS5E









































































































Reviews:

No comments