manualshive.com logo in svg

Bosch rexroth HS5E, Instruction Manual, Page: 57 / 104

Share
Download
Bosch rexroth HS5E Instruction Manual Download Page 57

RE 92076-01-B/2021-04-22, Bosch Rexroth AG

 

Installation |

 A4... with HS5E(V)(L) control system Series 1x and 30 57

/104

7.5  Performing flushing cycle

In order to remove foreign particles from the system, Bosch Rexroth recommends 
a flushing cycle for the hydraulic system before the first commissioning. To avoid 
internal contamination, do not include the axial piston unit in the flushing cycle.

Use an additional flushing unit to perform the flushing cycle. Follow the 
instructions of the flushing unit's manufacturer for the exact procedure during the 
flushing cycle.

7.6  Electrically connecting the HS5E(V)(L) control system

The machine or system manufacturer is responsible for the layout of the electric 
control.
For electrically controlled HS5E(V)(L) control systems, the electric control must be 
connected correctly according to the circuit diagram of the system manufacturer.

Damage to the device due to incorrect installation is not covered by the warranty!

1. 

Switch off the power supply to the relevant system component.

2. 

Connect the HS5E pilot control valve electrically (24 V).

7.6.1  Cable sets

Accessories for HS5E(V)(L)

Material number

Data sheet

Plug-in connector, 12-pin for central connection XH4
without cable (assembly kit) 

R900884671

08006

Plug-in connector, 12-pin for central connection XH4
with cable set 2 x 5 m

R900032356

Plug-in connector, 12-pin for central connection XH4
with cable set 2 x 20 m

R900860399

Pressure transducer HM 20-2X,
Measuring range 630 bar (4 ... 20 mA) 

R901342035

30272

Test device VT-PDFE-1-1X/V0/0

R900757051

29689-B

Compact power supply unit VT-NE32-1X

R900080049

29929

An Ethernet M12 to RJ45 connection cable (ports X7E1 & 
X7E2), additional information in type designation RKB0044/
xxx.x (xxx.x: length in meters)

R911172135

7.6.2  Wiring the electronic components

In general, the following applies:

 

– Keep the number of intermediate terminals as low as possible.

 

– You are not allowed to align electromagnetic sources of interference in the 

immediate vicinity of the HS5E pilot control valve.

 

– You are not allowed to route power cables in the vicinity of the HS5E pilot 

control valve.

Summary of Contents for rexroth HS5E









































































































Reviews:

No comments