Bosch rexroth HS5E Instruction Manual Download Page 45

Page: 45 / 104

RE 92076-01-B/2021-04-22, Bosch Rexroth AG

Installation |

A4... with HS5E(V)(L) control system Series 1x and 30 45

/104

t min

min

S max

t min

min

S max

ES min

t min

min

S max

R(L)

1, 2

R(L)

1, 2

R(L)

Einschraubloch M22

M10 (x1.5)

M16 (x2)

M8 (x1.25)

Einschraubloch M22

M10 (x1.5)

M16 (x2)

M8 (x1.25)

Ein

sch

raub
lo

10 (
x1.

16 (
x2)

8 (

x1.

25)

Fig. 13: Above-reservoir installation A4VSO with installation positions 4-6

Filling/air bleeding

min

Minimum required distance to
reservoir bottom (100 mm)

T, R(L)

Highest drain port

ES min

Minimum required height needed
to protect the axial piston unit from
draining (25 mm)

Suction port

S max

Maximum permissible suction
height (800 mm)

Baffle (baffle plate)

t min

Minimum required immersion depth
(200 mm)

Port

is part of the external piping and must be provided on the customer side

to simplify the filling and air bleeding.

Table 12: Above-reservoir installation

Installation position

Air bleed

Filling

4 (drive shaft horizontal)

R(L) (F)

5 (drive shaft horizontal)

T (F)

6 (drive shaft vertically down)

T (F)

7.4 Installing the axial piston unit

7.4.1 Preparation
1.

Compare the material number and designation (type code) with the parameters
in the order confirmation.

If the material number for the axial piston unit does not match the one in the
order confirmation, contact your local contact person for clarification. You can
find their contact information at

www.boschrexroth.com/addresses.

Summary of Contents for rexroth HS5E









































































































Search results

Summary of Contents for rexroth HS5E

Reviews:

Bosch rexroth HS5E, Instruction Manual, Page: 45 / 104

Search results

Summary of Contents for rexroth HS5E

Reviews: