Bosch rexroth HS5E Instruction Manual Download Page 48 | Manualshive

Page: 48 / 104

Bosch rexroth HS5E Instruction Manual Download Page 48

48

/104

A4... with HS5E(V)(L) control system Series 1x and 30

| Installation

Bosch Rexroth AG, RE 92076-01-B/2021-04-22

9.

For bell housing installation, check the coupling axial play through the bell
window according to the manufacturer's specifications.

10.

Details on the required tools and tightening torques for the mounting bolts are
available from the machine/system manufacturer.

11.

When using elastic couplings, check that the drive does not resonate after
completing the installation.

7.4.5 Installation on a gearbox

The following describes how to assemble the axial piston unit on a gearbox.
After installing on a gearbox, the axial piston unit is covered and is difficult to access:

▶ Before installing, make sure that the spigot diameter centers the axial piston unit

(observe tolerances) and that no excessive axial or radial forces are acting on the
drive shaft of the axial piston unit (installation length).

▶ Protect the drive shaft against frictional corrosion by providing permanent

lubrication.

▶ Fasten the axial piston unit at the installation location.

No gearing forces higher than the permissible axial and radial forces should act on
the shaft; if necessary, support the gear wheel at the gearbox output separately.

7.4.6 Installation with cardan shaft

The following describes how to connect the axial piston unit to the drive motor with
a cardan shaft.

Notice!

Damage to the axial piston unit and leaks at the shaft seal!

Improperly installed cardan shafts generate unbalances. This results in vibrations
and excessive forces on the drive shaft.

▶ Observe the cardan shaft manufacturer's assembly instructions.

1.

Position the axial piston unit near the intended installation location. Allow
enough space for the cardan shaft to fit through on both sides.

2.

Place the cardan shaft on the output shaft of the drive motor.

3.

Push the axial piston unit to the cardan shaft and place the cardan shaft on the
drive shaft of the axial piston unit.

4.

Bring the axial piston unit to the installation position and fasten it. If necessary,
details on the required tools and tightening torques for the mounting bolts can
be obtained from the system manufacturer.

7.4.7 Completion of assembly
1.

Remove any installed transport screws.

Use a suitable tool for this to prevent damage to the sealing and functional surface.
If the sealing or functional surface is damaged, contact your Bosch Rexroth service
partner or the service department of the manufacturer's plant for the axial piston
unit.

For attachment via gear

wheel or helical gear shaft

«
...
46
47
48
49
50
...
»

Summary of Contents for rexroth HS5E









































































































Reviews:

No comments