Bosch Rexroth CS 440RC Detailed Configuration And Set-Up Manual Download Page 52

Page: 52 / 57

52/57

Bosch Rexroth Canada ı 03.10.2011 ı Revision 5.4

How to check the Conveyor/Spinner/Prewet/Gate Operation modes?

The Conveyor mode and Material selected are shown on the top left Operator

Screen as: X-MAT001

•

X: A-Automatic/Closed, O-Open, M-Manual, C-Wt/Area

•

MAT001: Name of the Material selected

The Prewet mode and Liquid selected are shown on the top right Operator Screen

as: X-LIQ001

•

X: F-Fixed, V-Variable, M-Manual

•

LIQ001: Name of the Liquid selected

If the Gate Read Back is on a ‘R’ is added after the gate position, for instance, ‘Gate:

04 R’.

What is the default PASSWORD?

‘CS-440RC’ is the factory default password.

What is the Simulated Ground Speed and how to set up?

It simulates the ground speed signal, and to allows for diagnostics and calibration

without moving. To set it up, here are the steps:

•

Set to program mode by turning the programming key

•

Select SYSTEM SETUP->SPD SIM+ANTI-ICING->SPD SIM

•

Press ENTER key

•

Set back to operation mode

•

Press ESC to show operator screen

•

Scroll Up/Down to adjust ground speed

What are the m

What are the modes for BLAST?

odes for BLAST?

•

MAX OUTPUT, set to max valve output

•

STATIONARY MAX, set to max valve output irrelevant of ground speed

•

CLOSED LOOP, regulate to the configured BLAST rate

•

OFF

10.

How does the SOLID REDUCTION work?

It designed to reduce salt usage by a pre-configured percentage when PREWET is

used. Here are the steps to set up:

•

Turn the key to program mode

•

Select SYSTEM SETUP->OPERATION SETTINGS->SOLID REDUCTION

•

Set a percentage of reduction for each material

11.

What is the RETURN OIL PREWET?

Summary of Contents for Rexroth CS 440RC


























































Search results

Summary of Contents for Rexroth CS 440RC

Reviews:

Related manuals for Rexroth CS 440RC

Brands by name

Popular brands

Bosch Rexroth CS 440RC, Detailed Configuration And Set-Up Manual

Search results

Summary of Contents for Rexroth CS 440RC

Reviews:

Related manuals for Rexroth CS 440RC

Brands by name

Popular brands