Bosch Rexroth CS 440RC Detailed Configuration And Set-Up Manual Download Page 51

Page: 51 / 57

51/57

Bosch Rexroth Canada ı 03.10.2011 ı Revision 5.4

Spin Rate Spinner Rate, normally % output

Headers

Meaning

Ctrl Mode Conveyor control mode

Gate/Error Gate position in inches, and error code

Temp. Temperature

2. What is the spreading

2. What is the spreading time for an event in reports?

time for an event in reports?

Total Spread Time = Total Time - Blast Time - Pause Time.

Does the Total Time equal to

Does the Total Time equal to the difference between the start times of the

the difference between the start times of the

present event and the next event?

The only exception being in the case of a reboot, which will show up as an INIT
event.

4. What are the CS

4. What are the CS

4. What are the CS----440RC

440RC

440RC error codes and error messages?

error codes and error messages?

•

01 – Under-Application of Solid

•

02 – Under-Application of Liquid

•

03 – Output Non-Zero on a start up

•

04 – Blast too long

•

05 – Over Speed Warning

•

06 – Sensor Calibration Error

•

09 – Knob Input Failure

•

10 – PWM Output Failure

•

11 – MC08 System Error

•

12 – No Solid Material

•

13 – No Ground Speed

•

14 – No Conveyor Sensor

•

15 – No Flow Sensor

•

16 – No Gate Sensor

•

17 – Leaving Ground Speed Simulation mode, warning only

•

18 – Gate Position is zero, warning

•

20 – No communication between display and RC

Why does units of Total Dist. Trip Summary togg

Why does units of Total Dist. Trip Summary toggle between km/mi and pls?

le between km/mi and pls?

This field shows both Total Dist. in km/mi or Dist. in pulses. The field toggles

between two values each time Trip Summary is accessed. The feature can be used

to count pulses for a designated distance, which is one way to set up GROUND

SPEED input.

Summary of Contents for Rexroth CS 440RC


























































Search results

Summary of Contents for Rexroth CS 440RC

Reviews:

Related manuals for Rexroth CS 440RC

Brands by name

Popular brands

Bosch Rexroth CS 440RC, Detailed Configuration And Set-Up Manual

Search results

Summary of Contents for Rexroth CS 440RC

Reviews:

Related manuals for Rexroth CS 440RC

Brands by name

Popular brands