manualshive.com logo in svg

Bosch PRAESENSA PRA-AD604, Configuration Manual, Page: 69 / 164

Share
Download
Bosch PRAESENSA PRA-AD604 Configuration Manual Download Page 69

PRAESENSA

Configure the system | en

69

Bosch Security Systems B.V.

Configuration manual

2020-09 | V1.20 | PRAESENSA 1.20

5.4.2

System settings

1.

Below

 the System options page, 

click

 System settings:

–

A number of general, system wide parameters can be defined using the System
settings page.

2.

Select and set

 each of the following items:

Item

Value

Description

Rapid Spanning Tree
Protocol (RSTP)

Enable / Disable

Specifies

 whether the network forms a

redundant ring (

Enable

) or not (

Disable

). If

Enabled, network cable breaks are reported.
By default RSTP is enabled. See also 

Ethernet

adapter settings, page 30, if required.

Multicast address range

Selection
(IP‑address)

Select the IP‑address range from the
dropdown list.
Use when you want to share networks with
other equipment that uses multicast. Or
when you want to choose, for a 2

nd

PRAESENSA system, a non-conflicting
IP‑address range.

Allow access by
non‑configured system
clients

Enable / Disable
(Enabled by
default)

Specifies

 whether defined System clients

that are part of the system composition can
access the system (

Enable

) or not (

Disable

).

Call station display
timeout

Enable / Time
selection
(1‑10 minutes)

Enabled

 and after the Time selection, the call

station LCD goes to black and the selection
that was made is automatically cancelled if
the selection has not been executed.

IMPORTANT

: If a call station is not yet

configured, the LCD goes to black after 10
minutes.

Call station operator
language

Language
Selection

Specifies

 the call station display user

language for 

all

 LCD call stations used in the

system.

Amplifier output voltage  

70 V / 100 V

Specifies

 the amplifier output channel

voltage (70 V 

or

 100 V) of 

all

 PRAESENSA

amplifier outputs used in the system.

IMPORTANT

: After changing the output

voltage, save the configuration and restart
the system before doing a load measurement
on the amplifier outputs. Results of previous
measurements are wrong when the output
voltage selection has changed. See also
Amplifier loads, page 108.

UL amplifier mode

Enable / Disable When enabled, the amplifiers comply to the

requirements of UL with regards to
temperature limitations. When disabled, the
amplifiers run in the normal (EN54) mode.

Summary of Contents for PRAESENSA PRA-AD604





































































































































































Reviews:

No comments