manualshive.com logo in svg

Bosch PRAESENSA PRA-AD604, Configuration Manual, Page: 119 / 164

Share
Download
Bosch PRAESENSA PRA-AD604 Configuration Manual Download Page 119

PRAESENSA

Introduction to make an announcement | en

119

Bosch Security Systems B.V.

Configuration manual

2020-09 | V1.20 | PRAESENSA 1.20

Normal announcements

Normal announcements typically contain live speech and optionally tones and pre‑recorded
messages. The content of normal announcements is defined by a call definition. See 

Call

definitions, page 81.
Normal announcement is set in 

Call station, page 59 > Class > Normal.

Emergency announcements

Emergency announcements are similar to normal announcements. The major difference is that
emergency announcements put the system in the emergency state, if configured. In the
emergency state, PRAESENSA stops all BGM announcements and normal announcements, if
configured.
How the system acts could be set in the configuration > 

System settings, page 69 > Emergency

mode. Emergency announcement is set in 

Call station, page 59 > Class > Emergency.

10.3

Routing

The routing of the announcement is the set of zones and/or zone group to which the
announcement is intended to be addressed. Whether the announcement actually is addressed
to the selected zones and/or zone group depends on the priority of the announcement.

Summary of Contents for PRAESENSA PRA-AD604





































































































































































Reviews:

No comments